On the check, we come across to lots of details regarding SysRq at https://www.kernel.org/doc/html/v4.11/admin-guide/sysrq.html. If you prefer the RTFM mode, then please go forward and read the above URL.


What if a Linux system looks unresponsive to you? For several years, as a beginner, I used to do a power reset using the usual "Ctrl + Alt + Delete" or other keyboard shortcuts but still, it won’t work. And depending on the state of the file system, I may be faced with an fsck. However, there is something called SysRq key (System Request key) which will help you to shut down the system cleanly. You can see the SysRq written in the PrintScr key or could be Break key. Something you need to use the Fn key as well, like Fn+Alt+SysRQ+ “x”. For a physical console connection, pressing and releasing break and then pressing the Magic SysRq key would work. i.e no Alt key required.


Magic SysRq key, is a deadly key when used (read misused). Itʼs a direct line to the kernel or in other words, interrupt. You can easily check whether SysRq is allowed or not with the command ‘cat /proc/sys/kernel/sysrqʼ. If disabled, enable SysRq using one of several methods. Usually pass 1 to the file /proc/sys/kernel/SysRq. To make it permanently, add kernel.sysrq =1 in the /etc/ sysctl.conf. However, do note that the disabling or enabling of Magic SysRq keys is only referring to the ability to physically trigger them. You can trigger them also bypassing the keys as below. 

echo “b” > /proc/sysrq-trigger


While passing the key, please make sure that you understand what each “b”s and “c”s do. For example, if you do —> echo c > /proc/sysrq-trigger <— it would crash the Linux kernel.


Here is the list of possible values in /proc/sys/kernel/sysrq:

  • 0 – disable sysrq completely
  • 1 – enable all functions of sysrq
  • >1 – bitmask of allowed sysrq functions asee below for detailed function 
  • description
  • 2 = 0x2 – enable control of console logging level
  • 4 = 0x4 – enable control of keyboard aSAK, unraw)
  • 8 = 0x8 – enable debugging dumps of processes etc.
  • 16 = 0x10 – enable sync command
  • 32 = 0x20 – enable remount read-only
  • 64 = 0x40 – enable signalling of processes aterm, kill, oom-kill)
  • 128 = 0x80 – allow reboot/poweroff
  • 256 = 0x100 – allow nicing of all RT tasks


The normal value of "/proc/sys/kernel/sysrq" is as below:

$ cat /proc/sys/kernel/sysrq


The command returned a value of 176.  A “0” value disables all the SysRQ function and “1” enables all the features and values above 1 enables specific ones. Here we have a value of 176 which is obtained as a sum of “128” (which allows reboot and poweroff) + “32” (ability to remount filesystems in read-only mode) + “16”, which enables sync command.


To shut down the system after a really bad kernel panic, do the following, in sequence:

  • Alt+SysRQ+e (sends TERM-signal, processes can shutdown properly)
  • Alt+SysRQ+i (for the processes that didn’t listen for the TERM signal, this is (kill -9 process)
  • Alt+SysRQ+s (sync or properly flush any data to disks)
  • Alt+SysRQ+u (a sync will be done when unmounting anyway)
  • Alt+SysRQ+b (reboot)


First, you should send the “e” command to SIGTERM all processes thus allowing the opportunity for graceful exits. Processes unable or unwilling to respond to a SIGTERM will need to be handled with the “i” command (SIGKILL ALL THE THINGS). Then, youʼll need to perform Alt+SysRq+s to “sync” or properly flush any data to disks. Next, Alt+SysRq+u will remount all disks as read-only. Finally,  Alt+SysRq+b will reboot the system. When it comes up, you will not need to perform any file system checking, and you can rest peacefully knowing that you gave every running process your best try at allowing it to close gracefully and write any data to disk consistently.


To perform this process, press and hold the Alt + SysRq key combination and – while holding the Alt and SysRq keys down. To remember this, remember BUSIER, and apply in reverse, like REISUB. You may not need R always. R puts the keyboard to raw mode.


Let us take care of your servers 24/7/365. You can contact us at any time and get rid of all the hassles of server management. We are always ready to assist you.


Was this answer helpful? 0 Users Found This Useful (0 Votes)