MTR is a simple, cross-platform command-line network diagnostic tool that combines the functionality of commonly used traceroute and ping programs into a single tool. In a similar fashion as traceroute, mtr prints information about the route that packets take from the host on which mtr is run to a user-specified destination host.

 

However, mtr shows a wealth of information than traceroute: it determines the pathway to a remote machine while printing response percentage, as well as response times of all network, hops in the internet route between the local system and a remote machines.

 

How Does MTR Work?

 

Once you run mtr, it probes the network connection between the local system and a remote host that you have specified. It first establishes the address of each network hop (bridges, routers and gateways etc.) between the hosts, it then pings (sends a sequence ICMP ECHO requests to) each one to determine the quality of the link to each machine.

 

During the course of this operation, mtr outputs some useful statistics about each machine – updated in real-time, by default.

 

This tool comes pre-installed on most Linux distributions and is fairly easy to use once you go through the 10 mtr command examples for network diagnostics in Linux, explained below.

 

If mtr not installed, you can install it on your respective Linux distributions using your default package manager as shown.

$ sudo apt install mtr
$ sudo yum install mtr
$ sudo dnf install mtr

 

10 MTR Network Diagnostics Tool Usage Examples

 

1. The simplest example of using mtr is to provide the domain name or IP address of the remote machine as an argument, for example, google.com or 216.58.223.78. This command will show you a traceroute report updated in real-time until you exit the program (by pressing q or Ctrl + C).

$ mtr google.com
OR
$ mtr 216.58.223.78

Start: Thu Jun 28 12:10:13 2018
HOST: rootadminz                     Loss%   Snt   Last   Avg  Best  Wrst StDev
  1.|-- 192.168.0.1                0.0%     5    0.3   0.3   0.3   0.4   0.0
  2.|-- 5.5.5.211                  0.0%     5    0.7   0.9   0.7   1.3   0.0
  3.|-- 209.snat-111-91-120.hns.n 80.0%     5    7.1   7.1   7.1   7.1   0.0
  4.|-- 72.14.194.226              0.0%     5    1.9   2.9   1.9   4.4   1.1
  5.|-- 108.170.248.161            0.0%     5    2.9   3.5   2.0   4.3   0.7
  6.|-- 216.239.62.237             0.0%     5    3.0   6.2   2.9  18.3   6.7
  7.|-- bom05s12-in-f14.1e100.net  0.0%     5    2.1   2.4   2.0   3.8   0.5

 

2. You can force mtr to display numeric IP addresses instead of hostnames (typically FQDNs – Fully Qualified Domain Names), using the -n flag as shown.

$ mtr -n google.com

Start: Thu Jun 28 12:12:58 2018
HOST: rootadminz                     Loss%   Snt   Last   Avg  Best  Wrst StDev
  1.|-- 192.168.0.1                0.0%     5    0.3   0.3   0.3   0.4   0.0
  2.|-- 5.5.5.211                  0.0%     5    0.9   0.9   0.8   1.1   0.0
  3.|-- ???                       100.0     5    0.0   0.0   0.0   0.0   0.0
  4.|-- 72.14.194.226              0.0%     5    2.0   2.0   1.9   2.0   0.0
  5.|-- 108.170.248.161            0.0%     5    2.3   2.3   2.2   2.4   0.0
  6.|-- 216.239.62.237             0.0%     5    3.0   3.2   3.0   3.3   0.0
  7.|-- 172.217.160.174            0.0%     5    3.7   3.6   2.0   5.3   1.4

 

3. If you would like mtr to display both hostnames, as well as numeric IP numbers, use the -b flag as shown.

$ mtr -b google.com

Start: Thu Jun 28 12:14:36 2018
HOST: rootadminz                     Loss%   Snt   Last   Avg  Best  Wrst StDev
  1.|-- 192.168.0.1                0.0%     5    0.3   0.3   0.3   0.4   0.0
  2.|-- 5.5.5.211                  0.0%     5    0.7   0.8   0.6   1.0   0.0
  3.|-- 209.snat-111-91-120.hns.n  0.0%     5    1.4   1.6   1.3   2.1   0.0
  4.|-- 72.14.194.226              0.0%     5    1.8   2.1   1.8   2.6   0.0
  5.|-- 108.170.248.209            0.0%     5    2.0   1.9   1.8   2.0   0.0
  6.|-- 216.239.56.115             0.0%     5    2.4   2.7   2.4   2.9   0.0
  7.|-- bom07s15-in-f14.1e100.net  0.0%     5    3.7   2.2   1.7   3.7   0.9

 

4. To limit the number of pings to a specific value and exit mtr after those pings, use the -c flag. If you observe from the Snt column, once the specified number of pings is reached, the live update stops and the program exits.

$ mtr -c5 google.com

 

5. You can set it into report mode using the -r flag, a useful option for producing statistics concerning network quality. You can use this option together with the -c option to specify the number of pings. Since the statistics are printed to std output, you can redirect them to a file for later analysis.

$ mtr -r -c 5 google.com >mtr-report

 

The -w flag enables wide report mode for clearer output.

$ mtr -rw -c 5 google.com >mtr-report

 

6. You can also re-arrange the output fields the way you wish, this is made possible by the -o flag as shown (see the mtr man page for the meaning of field labels).

$ mtr -o "LSDR NBAW JMXI" 216.58.223.78

 

7. The default interval between ICMP ECHO requests is one second, you can specify the interval between ICMP ECHO requests by changing the value using the -i flag as shown.

$ mtr -i 2 google.com

 

8. You can use TCP SYN packets or UDP datagrams instead of the default ICMP ECHO requests as shown.

$ mtr --tcp test.com
OR
$ mtr --udp test.com

 

9. To specify the maximum number of hops (default is 30) to be probed between the local system and the remote machine, use the -m flag.

$ mtr -m 35 216.58.223.78

 

10. While probing network quality, you can set the packet size used in bytes using the -s flag like so.

$ mtr -r -s PACKETSIZE -c 5 google.com >mtr-report

 

With these examples, you should be good to go with using mtr, see the man page for more usage options.

$ man mtr 

 

Ця відповідь Вам допомогла? 0 Користувачі, які знайшли це корисним (0 Голосів)